Replacement Range Hood Fan Motor for RS-385 PHC2-17100B

Question

Question:

Hi. My range hood stove fan quit. MODEL # is: RS-385PHC2-17100B VD0218-00 13.6V 1.2A 3C0311 Is there a replacement part # or manufacturer for this? I can’t seem to find one. Thanks!

asked by: Marc

0

Expert Reply:

The Replacement 12V DC Motor for Ventline, Ventadome, and Vanair Fans # BVD0218-00 you were looking at can be used to replace your RS-385PHC2-17100B range hood fan. We've previously confirmed this with Ventline.

expert reply by: Erik B

0

Answer 1

The motor you'd looked at, part #BVD0218-00 is the correct replacement for your range hood. I've confirmed this by forwarding your photo to the folks at Ventline.

view full answer...

Answer 2

The correct replacement motor for your Rs-385phc2-17100b Vdo218-00 Kinmore Vent is going to be the Replacement 12V DC Motor for Ventline, Ventadome, and Vanair Fans Item #BVD0218-00.

view full answer...

Answer 3

We offer a direct replacement for your current 45A Parallax/Magnetek 6345 Power Center. The Progressive Dynamics Replacement Converter, part #PD4645V is exactly what you'd need. I've linked to a product description video for the…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 7

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept…

view full answer...

Answer 9

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 10

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 11

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 12

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Replacement Range Hood Fan Motor for RS-385 PHC2-17100B

Product Page this Question was Asked From

Continue Researching