How To Determine Fit of Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System

Question

Question:

Will your Lippert 3.0 4 point ground control system work on my 2014 Grand Design Reflection ? its a Fifth Wheel unit. I know I will need to drill the rear beam to attach the rear mounting plates. 2 questions, will that plate clear my slide bar which is only about 1 3/4 inches out from the beam. Second, will the front stabilizers fit exactly where the old ones are now? It looks like they are just bolted in, and the new ones should just in. thanks,

asked by: Joe B

0

Expert Reply:

The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC358590 is a mostly universal leveling system for fifth wheel trailers. The only way to confirm compatibility with a particular make/model would be to look though the install instructions and determine fit for yourself. The front jacks are direct replacements for the existing so there will be no issues there. The rear jacks however are what usually cause the most problems. There needs to be unimpeded space on the frame for the jacks to mount but so long as you do have space you'll be good to go.

expert reply by: Conner L

0

Answer 1

We have a online diagram that will help you understand how the break away system is wired into your trailer. It is actually a simple installation. The system splices into the existing trailer wiring. The break away box will have 3 wires coming out of…

view full answer...

Answer 2

Keystone fifth wheels like your Keystone Cougar 28SGS use very standard landing gear setups that the front jacks of a Lippert Ground Control #LC358590 will easily replace. This system would fit and work well on your Keystone Cougar 28SGS.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 7

Really you're going to need to measure the distance where the leveling system is going to be installed. If that distance is more than 20', then you're going to want the 6 point Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling…

view full answer...

Answer 8

The side plates of the B&W gooseneck trailer hitch #BWGNRK1313 will mount on the outside of each frame rail of your 2004 Dodge 2500 8-foot bed. See the B&W video I included at the 7 min and 30 second mark. If your Firestone air bags like…

view full answer...

Answer 9

The foot pad of the Replacement 22-1/2" Right Rear Leg for Lippert Ground Control 3.0 Electric Leveling System #LC428493 is welded to inner tube to jack to help shorter the total height for more clearance. The original model has the inner tube a…

view full answer...

Answer 10

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

How To Determine Fit of Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching