How High Above RV Roof Should Camco Gen-Turi RV Generator Exhaust System CAM44461 Be

Question

Question:

How high does the exhaust tube need to extend above roof line?

asked by: JC M

0

Expert Reply:

That's a good question, and the manufacturer recommends the Camco Gen-Turi RV Generator Exhaust System # CAM44461 extends 6 inches above the roofline of your RV.

The Gen-Turi is 120 inches, but there is an 18 inch extension if you need more height, the Camco Gen-Turi 18" Extension with Coupler # CAM44872.

I have added a link below to a video review for you to check out as well of the Camco Gen-Turi RV Generator Exhaust System # CAM44461.

expert reply by: Kyle S

0

Answer 1

The space that is between the outer wall of your coach and the exhaust pipe is going to depend on where your generator is and where the exhaust pipe you're connecting to is located. I can tell you that the 90 degree pipe on the bottom of the…

view full answer...

Answer 2

I went out to our warehouse and doublechecked the length myself and found the overall length of the Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe #CAM44812 to be 30" when including the bend. You are correct that the straight…

view full answer...

Answer 3

What you could do is use the 30 inch, 90 degree adapter for the Gen-Turi part #CAM44812 with the Gen-Ture part #CAM44461 to route the exhaust around the slide out.

view full answer...

Answer 4

The inner diameter of the expanded ends of the part #CAM44812 is 1.53 inches and the outer diameter of the non expanded end is 1.51 inches. So basically this setup is designed to either slip into a 1-1/2 inch pipe or slip over a 1-1/2 inch pipe.

view full answer...

Answer 5

Brake magnets are made to fit their specific brake assemblies. They are not made to be interchangeable between brake sizes or weight capacities. Some manufacturers do use different color magnet wires that correspond to the capacity. We know that…

view full answer...

Answer 6

Electric drum brake assemblies for 6k and 7k axles both use the same 5 bolt mounting pattern. The 7k brakes will have a stronger magnet and will provide more braking. If used on a 6k axle a 7k brake assembly can be too aggressive but it could be…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

How High Above RV Roof Should Camco Gen-Turi RV Generator Exhaust System CAM44461 Be

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching