Which TorkLift Super Hitch Trailer Hitch Receiver Fits A 2000 Ford Excursion?

Question

Question:

Will this hitch fit my 2000 Ford Excursion?

asked by: Christian M

0

Expert Reply:

I have another option for you, but the TorkLift SuperHitch Original Trailer Hitch Receiver - Custom Fit - Class V - 2" # TLD1109 you were looking at is only confirmed to fit select Ram Pickups and will not fit your 2000 Ford Excursion.

Instead I recommend the TorkLift SuperHitch Original Trailer Hitch Receiver - Custom Fit - Class V - Dual 2" Receivers # TLF1006 which is confirmed to fit your Excursion and has a 1700lb tongue weight rating and 17000lb trailer weight rating making it a great option for some heavy duty towing. Keep in mind your Excursion may not have the same capacities, so you will need to check the owner's manual to determine your towing capacity and use the lower rating between the vehicle and trailer hitch.

expert reply by: Samuel C

0

Answer 1

I have a very high capacity hitch I can recommend for your 2005 Ford Excursion, but the Curt part #C15410 is not it. Instead you would want the Torklift part #TLF1006 which is a confirmed fit and has a 1,700 lb tongue weight capacity and a 17,000 lb…

view full answer...

Answer 2

The TorkLift SuperHitch Original Trailer Hitch Receiver part #TLF1006 is designed to be a direct bolt on installation. It offers a 1,700 lb. tongue weight rating when used typically or 2,000 lbs. when used with weight distributionand will takes care…

view full answer...

Answer 3

The 2000 Ford Excursion is actually rated for 10,000 pounds gross trailer weight. The 18,000 pounds is the gross combined weight rating or GCWR. The GCWR is the most that the Excursion and trailer can weigh including cargo, passengers, and fuel. So…

view full answer...

Answer 4

To see installation details for both hitches, click the provided links. The Curt #C14011 installs using 18mm bolts that use existing nut plates in your Excursion's frame. No drilling is required to completed the installation. The hitch has a…

view full answer...

Answer 5

Both of the 2" receivers on the TorkLift SuperHitch Original Trailer Hitch Receiver - Custom Fit - Class V - Dual 2" Receivers #TLF1006 have the same tongue weight rating of 1700lbs and trailer weight rating of 17000lbs, Or 2000lb tongue…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Which TorkLift Super Hitch Trailer Hitch Receiver Fits A 2000 Ford Excursion?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching