Replacement Parts for Shelby 5854A Trailer Jack

Question

Question:

I have a shelby 5854a trailer jack, but I need the nut on the screw. Are those still available or something that will work?

asked by: Rob

0

Expert Reply:

I do have a solution for you, however replacement parts for your Shelby 5854A Trailer Jack are no longer available.

I recommend simply replacing your Shelby jack with a similar unit like the Fulton Bolt-Thru Swivel Trailer Jack # FXPD15L. This zinc plated marine jack has a lift capacity of 1,500 pounds and a total lift of 12 inches. It is a bolt-on installation and the hardware is included.

I have attached a short video demonstration on this product so you can get a better look at its features.

expert reply by: Chris R

0

Answer 1

It is possible the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit the same mount used by your Shelby 5776 jack but we do not have the exact dimensions of the mount used by your Shelby jack so you will need to take a quick…

view full answer...

Answer 2

To replace your plunger pin on your Shelby Jack I recommend Replacement Swivel Pin Kit for Trailer Jacks Item #DL22454. As long as your pin is 1/2" diameter this kit can replace your current pin.

view full answer...

Answer 3

Since Shelby is no longer in business, and jack handles are not universal, what that means is there isn't a replacement handle available, so your only option is to get a brand new jack. Since the Shelby is a weld-on jack, the best option we…

view full answer...

Answer 4

What you can try to do is manually spin the inner tube of the jack to get it to free back up. Then, lower or retract the jack after it has caught the gears again. The inner tube may be spinning freely as it is maxed out and the gears are not…

view full answer...

Answer 5

Shelby has been out of business for a number of years now and so there unfortunately are no replacement parts readily available. You might be able to find something where old parts are regularly sold, but you'll probably have to do a lot of…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

For your 2021 Chevrolet Blazer you're going to need to start with a base plate kit. Since there aren't any Blue Ox base plates I'd recommend going with the Roadmaster Direct-Connect Base Plate Kit #RM-523204-5. These are just as good as…

view full answer...

Replacement Parts for Shelby 5854A Trailer Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching