Will the Curt 56274 Wiring Harness Fit a 2021 Jeep Renegade Latitude

Question

Question:

will this work on a 2021 renegade latitude? # C56274?

asked by: Nicholas C

1

Helpful Expert Reply:

Yes. The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56274 is a confirmed fit on all trim packages of the 2021 Jeep Renegade including the Latitude trims. I've linked an installation video of this harness for you to check out, as well.

expert reply by: Erik B

1

Answer 1

The reason you want to run the power wire all the way up to battery is so that you bypass all of the delicate wiring of your vehicle. The power wire is required on trailer wiring harnesses for some vehicles because the electrical system on those…

view full answer...

Answer 2

A trailer hitch, such as the Draw-Tite #75282 that fits your 2017 Nissan Frontier, will need to be installed right side up. If you need height you can always use a ball mount that will give you the necessary amount of rise to line up with your…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Will the Curt 56274 Wiring Harness Fit a 2021 Jeep Renegade Latitude

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching