What Is The Distance Between Bottom Of The Bracket To Top Of Awning On Solera Awning LCV000168112

Question

Question:

What is the full height, from the bottom of the mounting bracket to the top of the roller, of a Lippert Solera slide topper? I have a Grand Design 295RL that has an awning attached to the dining room slideout, so Im trying to determine whether I can mount the topper on the flange and still have slope from the existing awning rail/rain gutter. Thank you.

asked by: Mike L

0

Expert Reply:

I had out warehouse measure the Solera RV Slide-Out Awning - 14'1" Wide - 48" Projection - Black # LCV000168112 you were looking at and from the bottom of the mounting bracket to the top of the roller measures in at 9-3/4" as shown in the included diagram, and the rail for the awning needs to be 3" - 6" above the top of the edge of the slide out.

I included a video of the # LCV000168112 for you to take a look at.

expert reply by: Samuel C

0

Dimensions Of Solera Awning # LCV000168112
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

Lippert Components purchased the Everchill line so we finally have some manufacturer support for the Everchill RV Refrigerator w/ Freezer Drawer #WAY44FR. I've attached the manual below to help you out.

view full answer...

Answer 9

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The measurement you will need is from the outside of the frame. The Ultra-Fab Power Twin II Stabilizers #UF39-941707 can be adjusted between 48-77 inches wide. The mounting brackets will sit under the frame with the outside of the angled metal…

view full answer...

What Is The Distance Between Bottom Of The Bracket To Top Of Awning On Solera Awning LCV000168112

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching