Recommended Grease for Wheel Bearings On Pop-Up Trailer

Question

Question:

Hello. I was wondering if you could suggest what type of bearing grease I should use for a pop up trailer. Thanks

asked by: Paul

0

Expert Reply:

Our install crew really likes the LMX Industrial Strength Grease # L11390 because of its high level of water insolubility. Even when wheel bearings are exposed to water, the LMX grease stays adhered to wheel bearings and other moving parts for long lasting protection which makes it a great all-purpose grease.

expert reply by: Mike L

0

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

To select a set of replacement idler hubs for your Fleetwood Destiny trailer you want to match up a few characteristics from your originals. These include the axle weight capacity, wheel bolt pattern and the bearing set used in the hubs. A…

view full answer...

Answer 3

The grease seal that is commonly used with the hubs that have inner/outer bearings of L44649 is the #RG06-020. These seals have an inner diameter of 1.50 inches and an outer diameter of 1.987 inches. You can measure yours to determine if this would…

view full answer...

Answer 4

I recommend the LubriMatic LMX Industrial Strength Grease #L11390 for your Dexter axle on your 2021 Vista Cruiser Travel Trailer. This grease is specifically formulated to work in extreme hot and cold temperatures under high pressures. It is also…

view full answer...

Answer 5

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Answer 8

Yes, the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-35-SA that you referenced are an exact replacement for the AxleTek assemblies you have now that have Axletek-10-GG stamped on them. If you check out the attached picture you can see the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...