Parts Needed to Add Brakes to 2011 Aspen Classic Tent Trailer

Question

Question:

I have a 2011 Aspen Classic tent trailer that I would like to install electric brakes on .I have a 5 lug drum. Do you k now where I can get a product that will meet my needs? I got these part numbers/descriptions from the Aspen Customer Service. #8 Torflex Suspension w/o brakes – Dexter Configuration #57507 #8 Torflex Suspension w/brakes – Dexter Configuration #57508 Dexter Parts Needed to add electric brakes: 1 K23-047-00 Left complete brake assembly 1 K23-048-00 Right complete brake assembly 2 008-257-91 Hub and drum assembly w/ 1/2” studs – 5 on 4.50 8 006-017-00 Brake mounting nuts Thanks,

asked by: Wayne F

1

Helpful Expert Reply:

For electric brake assemblies you need are part # 23-47-48 and then for hub/drums you'd # 8-257-5UC3-EZ which are a fit for the Dexter axles of your Aspen Classic.

expert reply by: Jameson C

1

Answer 1

I wish I could say we've had direct experience adding brakes to your trailer but at this time we have not nor has anyone requested help from us to do so. That said, I am sure we can help add brakes to the trailer but I was not able to find…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on…

view full answer...

Parts Needed to Add Brakes to 2011 Aspen Classic Tent Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching