Replacement Anchor Arm for an Elite Series 5th Wheel Hitch

Question

Question:

Would this part also be considered a replacement for the feet, nuts, arms, etc. in an Elite Series hitch? I have one but one of the arms broke and it looks like the only way to replace it would be to purchase the entire set. Is this true? Thanks.

asked by: Jim M

0

Expert Reply:

The Signature Series Adapter for Elite Series Rails, # RP58419, can be used as a replacement kit for the feet, nuts, bolts and arms for the Elite Series hitch if needed. These are the same arms and feet that are used on the Elite Series hitches and it is basically just a conversion kit for the older style Signature Series hitches.

expert reply by: John H

0

Answer 1

Yes, for an adapter to allow an older Signature Series Reese hitch to fit the Ford Hitch Prep package you would need the #RP58419.

view full answer...

Answer 2

Gen-Y currently only shows their 5" Offset #GY43XR only fitting the 2017 and newer Ford Super Duty trucks. I have included a drawing with the dimensions for this below you can check and see if it will fit your 2012 Ford F-350. If not another…

view full answer...

Answer 3

To my knowledge, the Reese Elite and Valley UBS (under bed system) were the only two manufacturers that offered a puck-style fifth wheel. If I recall correctly, the pucks were spaced differently. If you measure the center to center distance of the…

view full answer...

Answer 4

In regards to a Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter like part #RP94720 and a Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Adapter Pin Box like part #325-GH-8045, the main difference is that one uses air for…

view full answer...

Answer 5

When you install a fifth wheel rail kit like the custom kit part #RP50082-58 in the bed of your 2002 Ford Super Duty long bed the king pin center will be approximately 52-5/16 inches from the rear edge of the truck bed. The rear edge of the rear rail…

view full answer...

Answer 6

The actual weight of the #BWRVK3710 B&W Companion for the 2020+ GM factory puck system is 165 lbs. The head unit weights 75 lbs and the base weighs in at 90 lbs.

view full answer...

Answer 7

The B&W Companion OEM 5th Wheel Trailer Hitch w/ Slider #BWRVK3370 for your 2019 Ford F-250 has a total weight of about 265 pounds. Keep in mind though that the head on this particular hitch is really easy to remove so that you can lift the hitch…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 11

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Replacement Anchor Arm for an Elite Series 5th Wheel Hitch

Product Page this Question was Asked From

Continue Researching