What Size Hole Should be Drilled to Install a 4 inch Optronics Clearance Light

Question

Question:

I am installing these as a upgrade on my jeep. What size hole do i need to make in my jeep for these to fit into? Thanks

asked by: Philip P

0

Expert Reply:

You would want to drill a 4-1/2 inch hole to install the 4-inch Optronics Trailer Light # STL45RB.

You will also need a Straight 3-Wire Pigtail # A45PB to wire in the # STL45RB.

expert reply by: Jameson C

0

Answer 1

Super high-efficiency LED-type lights such as the Optronics #STL211RCB draw so little amperage (current) that you can wire them on your 20-foot trailer using 14-gauge (or heavier) wiring. We offer 10-gauge wire #10-1-1 by the foot. You will want to…

view full answer...

Answer 2

To install the Sealed, 4" Round LED Trailer Stop, Turn and Tail Light, Flange Mount Light #STL42RB that you referenced you will need to drill a 4-1/2 inch hole for the light to fit and the mounting holes will be 4-1/4 inches apart on center. For…

view full answer...

Answer 3

You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…

view full answer...

Answer 4

The closest backup light that we carry to the 4 Inch Round LED Trailer Light, #STL42RB, is the 4 Inch Round LED Backup Light, #BUL11CBX. This is a 4 inch round clear back up light that has an overall diameter of 5-3/4 inches and a depth of 1-5/8…

view full answer...

Answer 5

Because tail light #STL42RB has more than one function it has more than one amperage draw rating. Brake lights and turn signals draw more power so that will be the higher draw at 0.413 amps. Running lights use less power and would be the 0.26 amps.…

view full answer...

Answer 6

When it comes to wiring an LED taillight like the Sealed 4" Round LED Trailer Stop, Turn and Tail Light #STL42RB with Pigtail Harness, #A45PB, the red wire is for stop and turn, the black for running lights, and the white wire will need to be…

view full answer...

Answer 7

The king pin dimensions can be the same between fifth wheel trailers and large commercial trailers. Both types of trailers often use a standard 2 inch king pin although semis sometimes have a 3-1/2 inch. As long as your truck fits a 2 inch king pin…

view full answer...

Answer 8

A great choice for your boat trailer is the LED Trailer Light Kit for Trailers Over 80" Wide #TL16RK. This kit includes 2 tail lights which serve 8 functions (Stop, turn, tail, side marker, rear clearance, side reflector, rear reflector, and…

view full answer...

Answer 9

The Shelby 5404 winch is a 1,200 lb winch with a 20 foot nylon strap. The Dutton Lainson part #DL14996 is a similarly rated 1,500 lb winch and for a strap you would need the part #DL24249. This setup would be slightly stronger and less likely to bend…

view full answer...

Answer 10

The BoatBuckle Boat Winch Strap with Hook and Safety Latch part #IMF05848 will be the perfect replacement strap option for a Shelby Trailer Winch 5404. It's a 2" wide strap rated at 1,333 lbs.

view full answer...

Answer 11

The Replacement Entry Door Hinge for RV - 6 Leaf - White #LC198295 could very well be what you're needing for your 2001 Fleetwood Expedition 36T Diesel but even if you sent me pictures of your current hinges you would be the better judge of that…

view full answer...

Answer 12

There isn't a database for us to check the door based, only the manufacturer would be able to look up any info on it. The friction hinges #LC95VR and #LC22NJ that we carry are a universal fit so they will fit most RV doors but typically will not…

view full answer...