Distance from Pin Hole To Bottom of Plate on Brophy Stake Pocket Tie-Down Anchors

Question

Question:

I have a question about PK-SPTD. What is the measurement from the pin hole, to the bottom of the steel? I have a trailer where one set of stake pockets are impeded by the frame below it, so I have short clearance.

asked by: Andrew S

0

Expert Reply:

The distance from the top of the pin hole to the bottom of the steel plate for the Stake Pocket Tie-Down Anchors part # PK-SPTD is 1-3/4" which you can see in the attached photo.

expert reply by: Conner L

0

Brophy Camper Tie Down Dimensions
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…

view full answer...

Answer 9

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 10

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 11

The round or trunnion bars refers to the end of the spring bars. Round bars are typically designed for lighter applications, are a bit harder to install and are usually priced lower than trunnion bars. Trunnion bars are typically designed to be used…

view full answer...

Answer 12

Yes, you can get a set of lighter spring bars for the 8,000 lbs Blue Ox TrackPro Weight Distribution w/ Sway Control item #BLU67FR. They are the Replacement 600-lb Spring Bars for Blue Ox TrackPro Weight Distribution System item #BLU82FR.

view full answer...

Distance from Pin Hole To Bottom of Plate on Brophy Stake Pocket Tie-Down Anchors

Product Page this Question was Asked From

Continue Researching