Replacement Bearings, Races, Seal, and Studs for Trailer Hub 008-479-05

Question

Question:

Need quote and your part numbers for 1 each equivalent to each of the following Dexter part numbers: 010-010-00 seal And for equivalents to: 14125A/14276 cone and cup 25580/25520 cone and cup Also, if you can identify p/n for 1/2 x 20 wheel studs used in Dexter 008-479-05 hub-drum Thank you!

asked by: Mike T

0

Expert Reply:

The stud replacement you need for the 008-479-05 is the part number # K12WB2. The seal you need is # GS-2125DL, bearing # 14125A, race # 14276 and bearing # 25580 and race # 25520.

expert reply by: Jameson C

0

Answer 1

The standard replacement drive-in wheel stud for a 3,500 lb hub/drum like what you have on your Lippert 3,500 axle is the part #7-122 which is the correct thread size and length.

view full answer...

Answer 2

All of the hubs that we offer that are 3,500 lb capacity with a 6 on 5-1/2 inch bolt pattern are going to have 1/2 inch studs like the #AKHD-655-35-EZ-K. M12 is actually slightly smaller in diameter than that. For matching lug nuts though we have the…

view full answer...

Answer 3

We have replacement studs and hubs. You'll need to take some measurements of the lug stud like the dimensions on the attached picture of the Kodiak Wheel Bolt - 1/2" Diameter x 2" Long #K12WB2. This will help us to get you the right…

view full answer...

Answer 4

For your utility trailer, I recommend pulling one of the studs and measuring for fit. I've linked the picture measuring the Kodiak Wheel Bolt - 1/2" Diameter x 2" Long #K12WB2 for reference. You will need to use a digital caliper like…

view full answer...

Answer 5

The correct replacement wheel stud you need is the part #7-122 which is 2 inches long, has the thread diameter of 1/2 inch, and a spline diameter of .62 inch.

view full answer...

Answer 6

In order to replace the broken wheel stud on your Load Rite boat trailer, I recommend using the Trailer Hub Wheel Stud part #7-122 for a 2" long stud or the Trailer Hub Wheel Stud part #7-150 for a 2-3/32" long stud. You can measure your…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Bearings, Races, Seal, and Studs for Trailer Hub 008-479-05

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching