Can Reese Hitch Head # 58165 Fit on Reese Slider Base RP50024

Question

Question:

I have a Reese Pro Series 15000 hitch part #30056 I believe your part #58165. I want to know if I can put that head on your RP50024 round tube slider.

asked by: Michael H

0

Expert Reply:

As long as you had the hitch shoulder part number # 58179 with your hitch head part # 58165 yes you can use the round tube slider base part # RP50024 as well and have a complete slider hitch.

expert reply by: Jameson C

0

Answer 1

The Reese Crossmember, #RP58147 which uses a center pin to hold the hitch head will not accept the 15K Dual Pivot Pro Series Hitch head due the design variance. The Pro Series Head Support that was designed for your hitch is part #58179 and will…

view full answer...

Answer 2

Yes, the Reese/Pro Series fifth wheel hitch you have, part number 30077, is designed to fit the rail dimensions of the #RP56009-53 that you also referenced so this kit would work well for you. Since this is an outboard kit it will install much easier…

view full answer...

Answer 3

Is your Furrion Over the Range RV Convection Microwave #FMCM15SS working with other settings? I reached out to my contact at Furrion and they said if the fan and heat aren't working but the microwave is getting power then the unit needs to be…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Can Reese Hitch Head # 58165 Fit on Reese Slider Base RP50024

Product Page this Question was Asked From

Continue Researching