Air Lift 72704 Remote Not Working.

Question

Question:

I’ve changed the battery but the remote won’t come on. Any suggestions?

asked by: Randy

0

Expert Reply:

Start off by double checking that you have everything installed correctly and that you have installed two CR2032 batteries in your Remote for Air Lift WirelessONE Compressor Systems # AL72704. If you check out the attached clip from the instructions you can make sure everything is installed correctly. There is a specific way to stack the batteries for installation to work.

If you have followed all of these steps and the remote still isn't working properly let me know and I can help you troubleshoot further.

expert reply by: Les D

0

click to enlarge

James

4/26/2024

Battery is good. Remote lights up but no pump when trying to inflate. Have 12 volts at pump this happened before and had to buy a new remote.

Reply

Answer 1

To get your remote #AL72704 to work properly, you will need to sync it since the battery was replaced. To sync the remote use the following steps: 1. Turn ignition on. 2. Locate the sync wire in the wire harness of your Air Compressor. It will be…

view full answer...

Answer 2

I do have some info on how to change the batteries in your Replacement Remote for Air Lift WirelessONE Compressor System for Air Helper Springs #AL72704. I took a look at the instructions of the Air Lift WirelessONE Compressor System #AL25980 and…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference is the generation of the Air Lift Wireless One compressor kit the remote was designed for. The part #AL72704 fits the older style that was not Bluetooth compatible whereas the #AL39NV fits the #AL25980 which is the current version of…

view full answer...

Answer 5

I went to the warehouse and pulled one of the Remote for Air Lift WirelessONE Compressor System, part #AL72704. I have attached a photo of the remote you can check out. On each side of the remote in the areas with the red arrows, there is a small…

view full answer...

Answer 6

Generally this is an issue with the remote #AL73002 communicating with the system #AL74000, a blockage, or a leak. I would inspect the compressor system and all of the air lines to make sure there are no issues. You can check for leaks using soap and…

view full answer...

Answer 7

If you are trying to program a new controller for the #AL74000 Air Lift WirelessAIR Compressor System, it is the older model that references the yellow wire for pairing. This is no longer needed with the new model, which is why you cannot find the…

view full answer...

Answer 8

If following the pairing instructions for the controller on the Air Lift WirelessAIR Compressor System #AL74000 did not resolve your issue, you will also want to check for any blockage or leaks in the system. Simply make sure that all of the air…

view full answer...

Answer 9

When installing an Air Lift wireless compressor system on your 2015 Chevrolet Silverado 1500, like part #AL74000, a guaranteed fuse to use would be the one for the Radio. This is labeled as fuse 18 in the fuse panel that is on the passenger side of…

view full answer...

Answer 10

Since the remote on your Air Lift WirelessAIR Compressor System for Air Helper Springs - Remote - Bluetooth #AL74000 was working just fine and then stopped I recommend checking that the ground of the manifold is not underneath the foot of the…

view full answer...

Answer 11

There aren't necessarily any tricks to getting the Replacement Remote for Air Lift WirelessONE Compressor System, #AL72704 synced, but according to the Air Lift Installation Guide, this is what you'll need to do. 1. Turn ignition on. 2.…

view full answer...

Answer 12

In the settings mode of the controller you can join the manifolds with the controller. To set the manifold into join mode locate the yellow join wire. It is the yellow wire with heat shrink on the end of it. Remove the cap leaving it attached to the…

view full answer...

Air Lift 72704 Remote Not Working.

Product Page this Question was Asked From

Continue Researching