Is Replacement Hinge For Extang Trifecta and eMAX Tonneau Covers Passenger And Driver Side Specific

Question

Question:

Good morning I am looking to purchase ex 1032. I m curious if it is the same part for passenger side or if there is a difference? I have a trifecta soft tonneau cover. Ty

asked by: Daryl E

0

Expert Reply:

The Replacement Hinge for Extang Trifecta and eMAX Soft Tonneau Covers # EX1032 you were looking at will replace either the driver or passenger cab side hinge.

If you are needing the tail gate side hinge you will need the # EX1033 instead.

I included videos for each of the products mentioned for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The replacement hinge for the panels of the Extang Trifecta 2.0 is the hinge part #EX83645-64. Your picture didn't make it through but I attached a picture of what this hinge looks like installed. If you send me the picture you have I can check…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You would want the whole hinge assembly, #EX1033, especially if you have frequent breakage like you have described. There could be fatigue to the other components so to ensure maximum longevity I do recommend the whole hinge assembly. It is possible…

view full answer...

Answer 9

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

The Extang #EX1032 replacement hinge that you referenced is made for Extang Trifecta and Extang eMAX folding tonneau covers as a hinge replacement. I reached out to my contact at Extang and found out that they also make the Gator covers and that this…

view full answer...

Is Replacement Hinge For Extang Trifecta and eMAX Tonneau Covers Passenger And Driver Side Specific

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching