Availability Of A King Pin For 5th Wheel Trailer

Question

Question:

I need the king pin only.

asked by: Sari K

0

Expert Reply:

We do offer just the king pin like the Buyers Products 2" Forged SAE Trailer King Pin with 1/2" Bolster Plate # 337KP20050 which gives you the standard 2" king pin for use with a 5th wheel hitch.

It is a good idea to have a qualified welder install the king pin, as the welds need to be sound to support the weight of the trailer.

I included a video of the Buyers # 337KP20050 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The king pin dimensions can be the same between fifth wheel trailers and large commercial trailers. Both types of trailers often use a standard 2 inch king pin although semis sometimes have a 3-1/2 inch. As long as your truck fits a 2 inch king pin…

view full answer...

Answer 2

We don't have a 2 inch receiver application, but we do have the B&W Turnoverball King Pin Adapter for Trailers with Inverted 5th-Wheel Hitches #BWGNXA4000 which is a 2-1/2 inch outer measurement on the solid square. We also have the Fifth…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Availability Of A King Pin For 5th Wheel Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching