Replacement Pull Cables for Thomas Payne RV Recliners

Question

Question:

Hello, I have a Grand-A_Design Momentum 5th wheel that has a Thomas Payne rv couch recliner that the pull cable has broken. Do you have the replacement cable for this couch?

asked by: Michael W

0

Expert Reply:

Yes we do have replacement pull cables for the Thomas Payne RV recliners like what you have with the part # LC381462.

expert reply by: Jameson C

0

Answer 1

When replacing a Pull Cord for Thomas Payne #LC381462, the easiest way to get to the cord is to flip the seat over. This allows you access to disconnect the cord and remove the screws that hold the seat to the frame. Loosening the seat will allow you…

view full answer...

Answer 2

Yes. Assuming that you have a Thomas Payne brand theatre seat in your 2018 Grand Design Reflection, then the #LC381462 will work for you. If your furniture was manufactured by a different company, then this may not work. Thomas Payne did make theatre…

view full answer...

Answer 3

The Replacement Pull Cord for Thomas Payne Heritage Theatre Seating Recliners and Love Seats #LC381462 are made with a sturdy plastic handle and metal spring construction. While how often it would need to be replaced is really dependent on its use,…

view full answer...

Answer 4

Yes, I contacted Thomas Payne and the replacement pull cord for the Thomas Payne Heritage Recliner part #195-000022 is part #LC381462. This pull cord is the replacement pull cord for the Thomas Payne Heritage Theatre seating recliners and loveseats.…

view full answer...

Answer 5

You will need to disassemble the Thomas Payne Momentum RV Dual Reclining Sofa #195-055-056-058 in the same way it was assembled in order to remove the center console. Since each piece slides into the adjacent piece you are going to have to remove…

view full answer...

Answer 6

There could be 2 different issues here, so I'll give you a way to test out the control box which will help us figure out what the issue might be. To test the heater unplug the red and black wires from the control box (located behind and under…

view full answer...

Answer 7

For only one side of the awning working, since the motor is only on one side for the drive head, it is likely that the idler head on your awning is what needs replacing. I'm not 100 percent sure what you are referring to by front or rear joint,…

view full answer...

Answer 8

What I recommend doing is swapping the Control Box #195-387596 from the working side to the side that isn't working to see if that makes a difference. If it does then you'll want to get a replacement using the part above. If it doesn't…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Pull Cables for Thomas Payne RV Recliners

Product Page this Question was Asked From

Continue Researching