Trailer Bearing with Inner Diameter Close to 1.80 inch

Question

Question:

Hello. I am looking for inner bearing that is little bit bigger then 1.75 inch. My axle is 1.80

asked by: Andrey

0

Expert Reply:

The bearing we offer that has the closest inner diameter to 1.80 inch is the part # 603049 which has an inner diameter of 1.781 inch. The outer diameter is then 3.063 inch.

If you aren't totally sure what your spindle diameter is we have the digital caliper part # PTW80157 you could use to verify the dimension.

expert reply by: Jameson C

0

Answer 1

We do have the bearing #603049 which has an ID of 1.781" but it has as OD that is slightly larger than the #25580 bearing so you wouldn't be able to use the same race. This bearing has an OD of 3.063". We don't…

view full answer...

Answer 2

It can be very difficult to tell the difference between 6000 and 7000 lb axles because they both typically have a 3 inch diameter. Most of the components for your axle will cover both capacities, so the only way to tell is to look for markings on…

view full answer...

Answer 3

There is no specific torque rating for shackle bolts. You'll want to ensure that the bolts you use are long enough so that when installed you will have at least 2 threads protruding from the nut. Make sure that the bolt you're using…

view full answer...

Answer 4

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws…

view full answer...

Answer 5

Typically trailers will carry more of their weight on the front of the trailer, so you would want to put the brakes on the front axle as it will most likely carry more weight while braking. Also, when braking, weight will shift forward from the…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Trailer Bearing with Inner Diameter Close to 1.80 inch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching