Replacement Fabric for TruXedo Lo Pro Tonneau Cover On 2015 GMC Sierra 2500 6.5 Bed

Question

Question:

Looking for replacement fabric for my Truxedo Lo Pro bed cover on my 2015 GMC 2500HD short bed.

asked by: Scott E

1

Helpful Expert Reply:

The correct replacement fabric for the TruXedo Lo Pro Soft Roll-up Tonneau Cover on a 2015 GMC Sierra 2500 6-1/2' bed is part # TX572001-CVR.

expert reply by: Conner L

1

Answer 1

Yes, the Replacement Cover for TruXedo Lo Pro QT #TX572001-CVR is made by TruXedo. I confirmed with my contact at TruXedo that the replacement cover will have all of the TruXedo decals and labels. She did mention that the Lo Pro decal may look…

view full answer...

Answer 2

According to the manufacturer, putting one Valterra Folding Manual Stabilizer #020106 next to your entrance steps and one at the rear bumper of your trailer will do the most to prevent sway when you are entering and exiting your trailer. Keep in mind…

view full answer...

Answer 3

There is nothing that says you can't use Valterra Folding Manual Stabilizer #020106 for support for the back ramp door on your toy hauler. You would need at least 14 inches of clearance between the ground and the bottom of the ramp door when it…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

The Triple-Axle Trailer Hanger Kit #APTT3 that you referenced is designed to work on axles with capacities of 2,000 lbs to 7,000 lbs so it should work very well for you. I attached a picture that has a chart that shows exactly how you should space…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

In order to calculate where the axles would go on your trailer, there are several things that need to be taken into consideration. You will have to mock up the trailer with the suspension and axles to get the weights needed to determine where the…

view full answer...

Answer 11

Yes, the Replacement Cab End Corner and Weather Seal Kit for TruXedo TruXport Tonneau Covers #TX1118262 would be a compatible fit for your cover. If you need to replace the rear caps as well then you'll need part #TX1704534, #TX1704535 , and…

view full answer...

Answer 12

Different trailer configurations require different equalizers. It all depends on the springs, axle spacing, hanger spacing, height needed and so on. In many cases if you want to change the equalizer to something with different measurements you would…

view full answer...

Replacement Fabric for TruXedo Lo Pro Tonneau Cover On 2015 GMC Sierra 2500 6.5 Bed

Product Page this Question was Asked From

Continue Researching