Curt Brake Controller Wiring Harness for 2007 Ford F-350

Question

Question:

Will the C51432 brake controller harness work on a 2007 Ford F-350? If not, do you have one that will? Thanks

asked by: William G

0

Expert Reply:

The correct Curt brake controller vehicle specific wiring harness for a 2007 Ford F-350 would be part
# C51372. This harness is only compatible with Curt brake controllers such as the # C24VV Curt TriFlex.

The # C51432 you referred to is a fit for later model Ford Super Duty trucks, and wouldn't work for your 2007.

The harness would plug into the connector clipped to the rear of the storage pocket located above the ashtray, as shown in the provided photo.

expert reply by: Mike L

0

click to enlarge

Answer 1

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 2

On your 2002 Ford F-250 you will need to connect the Red wire to the Black wire on the brake controller for +12 Volts power and the Light Green wire to the Red Stoplight wire on the brake controller. The Dark Blue wire is connected to the Blue wire…

view full answer...

Answer 3

Using the Curt brake controller wiring harness #C51372 you will plug it in at the factory connection point. The built-in brake control wiring harness is located behind the dashboard. To reach the connector, remove the storage pocket that is built…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The brake controller port on a 2021 Ford F-150 (if equipped) will be located behind the coin tray in the center console. This will be accessed by removing the panel under the steering wheel. I have attached a video which shows this below. For a brake…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...