Correct Camper Tie-Downs for a 2020 GMC Sierra 1500 5-3/4' Bed

Question

Question:

Ineed to know for my new truck it is a 2020 GMC Sierra 1500 5.5

asked by: John E

0

Expert Reply:

The correct TorkLift Custom Frame-Mounted Camper Tie-Downs for a 2020 GMC Sierra 1500 5-3/4' Bed will be part # TLC2224 for the front and part # TL54FR for the rear if you have dual exhaust or part # TLC3220 if you have a single exhaust.

expert reply by: Conner L

0

Answer 1

Yes, the Timbren Suspension Enhancement System #T28MR will be the best option when it comes to cost-effectiveness. This will fit with your 2021 Chevrolet Silverado 1500 Z71 Trail Boss but you'll want to make sure these fit the gap properly. The…

view full answer...

Answer 2

We do have a solution for your needed parts however, I inquired about individual parts purchase for the TorkLift Custom Frame-Mounted Camper Tie-Downs #TL54FR & #TLC2224 and these are only sold in kit form. So while we can supply you what you…

view full answer...

Answer 3

For Torklift camper tie downs for your 2021 GMC Sierra 1500 with running boards and dual exhaust you'd want the part #TLC2224 for the front and part #TL54FR for the rear. This fits with dual exhaust as well.

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 11

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...