Front Mount Receiver Hitch for 2020 Chevy Tahoe
Question:
2020 Chev Tahoe. The 2 that are listed are mounted below the front bumper. This will be used on a rough construction site that requires as high as possible clearance. Item #65050 goes thru the front bumper. Is there a similar option for the Tahoe?
asked by: Roger C
Expert Reply:
As you mentioned, the Curt # C31073 and Draw-Tite # 65064 are the only front mounted receivers we offer for your 2020 Chevy Tahoe. Both hitches have the receiver located under the front bumper, which is necessitated by the way the vehicle front clip sits in relation to the frame members the hitches bolt onto. The way the vehicle is designed would prevent the receiver from sitting any higher on the front of the vehicle.
If I had to choose between the two, I'd go with the Curt model, as it's manufactured in the US.
Draw-Tite offers a front mounted skid shield, part # 6771 that would help protect the receiver from being damaged if you should bottom the receiver out. You'd also need a # PC3 hitch pin or a # e98882 hitch lock.
Products Referenced in This Question
Front Mount Trailer Hitch Receiver Skid Shield - 2" Hitch
- Accessories and Parts
- Front Receiver Hitch
- Skid Shield
- Draw-Tite
more information >
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Front Receiver Hitch
- Custom Fit Hitch
- Front Mount Hitch
- 500 lbs Vert Load
- 9000 lbs Line Pull
- 2 Inch Hitch
- Square Tube
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Stainless Steel
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Front Receiver Hitch
- Custom Fit Hitch
- Front Mount Hitch
- 500 lbs Vert Load
- 9000 lbs Line Pull
- 2 Inch Hitch
- Square Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How to Winch a Boat and Trailer Down a 60 Foot Hill with 35 Degree Slope
- Q&A: Winch Recommendation to Pull Boat Trailer Up Hill
- Q&A: Can I Operate the Trailer Valet XL Trailer Dolly on a Decline?
- Q&A: Do I Need to Disengage the Brakes on my Trailer When Using the Trailer Valet XL
- Q&A: Will a Front Hitch Help My Ability to Maneuever a Trailer In Tight Spaces
- Q&A: Will the Hitch Pin Hole on the Curt Front Hitch part # C31069 be In Front or Behind Air Dam
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Measure for Trailer Hitch Drop
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: The 5 Best Trailer Drop Hitches You Can Buy
on Front Receiver Hitch
