Replacement Trailer Hub Grease Seal with Outer Diameter 2 inch and Inner Diameter 1-3/8 inch

Question

Question:

I need two seals for my boat trailor bearings. The inside diameter is 1 3/8 and the outside is 2.00.

asked by: John G

0

Expert Reply:

Based on the dimensions listed we have the bearing kit part # BB60001 which has an outer diameter of 1.980 inches and an internal diameter of 1.375 inch. You'd want to use a digital caliper like # PTW80157 to verify that your dimensions are the same since the dimensions have to be exact.

expert reply by: Jameson C

0

Answer 1

Yes the bearing kit part #DL21792 is the correct kit for your trailer hub BT-100. This comes with two bearings L44643 like we know fit that hub part number.

view full answer...

Answer 2

Part #168233, appears to be a close match to your existing grease seal with 2-5/16" (2.3125) OD and 1-11/16" (1.6875) ID. It has an ID of 1.688", OD of 2.332" and a thickness of 0.38". Although I wasn't able to cross…

view full answer...

Answer 3

Many times when adding grease with the Bearing Buddy, a customer will add too much grease and blow out the rear grease seal which causes just what you say is happening to your wheel. I am sorry but to really be able to tell you what bearing kit you…

view full answer...

Answer 4

The Bearing Buddy Grease Seal Kit, #BB60001, is compatible on spindles that use the L44646 inner wheel bearing. The seals ID is 1.375 inches, but the stainless steel rings that slide over the spindle fit the 1.275 inch seal surface on the spindle.…

view full answer...

Answer 5

You are needing our Trailer Idler Hub Assembly #AKIHUB-440-2-G-1K. It is identical to the Trailer Idler Hub Assembly #AKIHUB-440-2-G-2K that you have on hold only it has the #L44643 Bearings that you need.

view full answer...

Answer 6

It sounds like you are looking for the correct grease seal for your spindle. If your inner bearing is part #L44643 and the grease seal journal, or mounting location, on the spindle is 1.25 inches, then you have two grease seal options. For a standard…

view full answer...

Answer 7

You can use any of three spindles with the Trailer Hub Assembly - 2,000 lbs Axles - 5 on 4-1/2, item #34822545BX. I have listed these spindles below. #TRU94FR - BT8 Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter #TRU59FR - BT8 Spindle for…

view full answer...

Answer 8

A non-tapered spindle with a 1.00" diameter will use an #L44643 inner and outer bearing, so you'll want to use the Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized #AKIHUB-440-2-G-1K, which have a 4 on 4 bolt pattern and…

view full answer...

Answer 9

For a 1 inch spindle on a boat trailer, I recommend the Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized #AKIHUB-545-2-G-1K or the Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized #AKIHUB-440-2-G-1K. These…

view full answer...

Answer 10

For a hub like the Dexter #34822BX that has a hub bore diameter of 1.98-inches, you'll want to use stainless steel Bearing Buddy #BB1980A-SS. These will provide the best resistance to corrosion and will allow the boat trailer's wheels to be…

view full answer...

Answer 11

Thank you for that information, and we do have a hub that fits a BT8 spindle and has a 4 on 4 bolt pattern. This hub is for a 2,000 lb axle, and is galvanized to protect it from corrosion, which is what you'll need for a boat trailer. The correct…

view full answer...

Answer 12

If both the inner and outer bearings are L44643 then you have a BT8 spindle. You can use #R104BT8, #TRU97FR, or #TRU59FR. All three of these spindles are rated for 1,000 pounds by themselves so they would be on a 2,000 pound axle. I have linked…

view full answer...

Replacement Trailer Hub Grease Seal with Outer Diameter 2 inch and Inner Diameter 1-3/8 inch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching