Does the Fusion Software Need To Be Installed On the Edge Diesel CTS3 Tuner Before Using

Question

Question:

I just got my edge evolution cts 2 tuner. Do I have to download the fusion software or can I just plug it in and have it work?

asked by: Patrick

0

Expert Reply:

The Edge Diesel Evolution CTS2 Performance Tuners like part # EP96TR will work straight out of the box just by plugging into the vehicle. That said, I do recommend following Edge's recommendation of updating the tuner beforehand via plugging it into a computer which is what is referenced as the Fusion Software.

expert reply by: Conner L

0

Answer 1

Yes the Torklift Lithium Battery Box part #TLA7700L that you referenced can be used with non-Lithium batteries like your 6 volt battery. The only thing that differentiates this from non-Lithium battery boxes is the size of the box since Lithium…

view full answer...

Answer 2

The holes on the bottom of the TorkLift PowerArmor Locking Battery Box #TLA7700L aren't necessarily designed for mounting the box and are really there to allow moisture to escape and as access holes for wiring. According to the instructions there…

view full answer...

Answer 3

Yes the internal dimensions of the TorkLift PowerArmor Locking Battery Box #TLA7708R that you referenced is easily compatible with carrying two of the batteries you mentioned. Check out the picture I attached to see the internal dimensions.

view full answer...

Answer 4

The box without the solar panel you are looking for is the TorkLift PowerArmor Locking Battery Box - 6V and 12V Batteries #TLA7708R; this is exactly the same as the TorkLift PowerArmor Solar Locking Battery Box #TLA7708RS with the only difference…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 9

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 10

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Does the Fusion Software Need To Be Installed On the Edge Diesel CTS3 Tuner Before Using

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching