Can I Use Tire Valve Extentions with TPMS Sensors

Question

Question:

Can I put 135Degree tire pressure valve extensions on and still put on a TPMS sensor

asked by: David L

1

Helpful Expert Reply:

Adding a TPMS sensor to a Wheel Masters Tire Pressure Valve Extenders part # WM8029135 with the 135 degree bend will be fine if using them with a metal valve stem on the rim which most have.

The reasoning is that if you add weight that far away from the attachment point it can cause issues with flexing the rubber and causing failure.

expert reply by: Randy B

1

Answer 1

We can get your 2020 Tiffin Wayfarer 24TW motorhome set up with a tire pressure monitoring system (TPMS), and the best option is from TireMinder. The reason for that is they have the most accurate psi readings, as well as tire sensors with long…

view full answer...

Answer 2

For the Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" Dually - Hub Mount - 135-Degree Bend #WM8001-135, the inner hose is 13 inches straight and the outside hose is 9-1/2 inches. I've attached a photo to help.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 11

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 12

I would be happy to! To flat tow your 2024 GMC Canyon Denali you will need the following parts: Tow Bar and Safety Chains - Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights item #RM-676 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit…

view full answer...

Can I Use Tire Valve Extentions with TPMS Sensors

Product Page this Question was Asked From

Continue Researching