Replacement Lead Leg Needed for Lippert Components LG-6000 Landing Gear

Question

Question:

I have a 2010 Wildwood RV with the Lippert Components LG-6000 landing gear system. One leg has stripped out in the worm gear assembly and i need a new lead leg for it.

asked by: Chad R

0

Expert Reply:

The Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin # LC179013 is the replacement you are seeking for your 6,000 lb capacity landing gear.

expert reply by: Jason S

0

click to enlarge

Answer 1

The Lippert landing gear part #LC333964 that you referenced can fit a trailer that has weld stops that are at a different dimension. Basically you would just have to have yours moved and rewelded.

view full answer...

Answer 2

Thread damage to the screw/nut inside of a jack is usually a result of over extending the trailer jack. I'm not saying that is what happened to you but that is the cause of the majority of these situations. Is your jack still covered under…

view full answer...

Answer 3

Essentially the #LG-196308 and the #LC196308 are identical. I'd go with the lower priced of the two since neither is a better choice than the other.

view full answer...

Answer 4

There is a great chance either of the legs you mentioned would work as a replacement, but I'd need to know for sure what landing gear you have on your trailer. The Lippert landing gear like the part #LC179013 and #LC179014 are very popular and…

view full answer...

Answer 5

The Stromberg Carlson Replacement Motor #LG-196308 and the Lippert HD Motor #LC196308 referenced in your question are essentially the same motor. They can be used interchangeably on a landing gear system. With this in mind, I simply recommend…

view full answer...

Answer 6

Stromberg Carlson Follow Leg #LG-179014 and Lippert Follow Leg #LC179014 are basically the same. Stromberg Carlson purchases parts from Lippert so a lot of their products are nearly identical to each other.

view full answer...

Answer 7

For the Kenda 215/60-8 Bias Trailer Tire and 8 Inch Wheel, #AM3H320, it measures 18.3 inches in diameter and it is 8.9 inches wide. This is going to have a smaller diameter than a 5.30x12 tire and wheel but it will be much wider, up to about 4 inches…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Replacement Lead Leg Needed for Lippert Components LG-6000 Landing Gear

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching