Lippert Electric A-Frame Trailer Jack 1817941 Stripped Threads on Screw/Nut
Question:
The inner tube assembly pressed in threads that the threaded shaft uses to raise and lower the unit striped under normal use causing the camper to fall and from what Ive read there is no replacement parts only had the camper 3 years with not a lot of use this should not have happened
asked by: David A
Expert Reply:
Thread damage to the screw/nut inside of a jack is usually a result of over extending the trailer jack. I'm not saying that is what happened to you but that is the cause of the majority of these situations. Is your jack still covered under warranty? If so then it may be able to be taken care of through a warranty claim. The screw/nut are not available as replacement parts.
For a replacement jack I would use the Stromberg Carlson # JET-3755 electric jack that has 24" of lift rather than the 18" lift that your broken jack has. It also has an optional "drop foot" that will give you another 5" of lift when needed. You might also consider the Fastway # FA88-00-6500 flip down foot that gives you 6" of lift.
Products Referenced in This Question
Fastway Flip Automatic Fold-Up Jack Foot for 2-1/4" Jacks - 6" Extension - 1,400 lbs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- 2-1/4 Inch Diameter Tubing
- Fastway
more information >
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 24" Lift - 3,500 lbs - Black
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- Leveling Jacks
- Tongue Jack
- Steel
- 3001 - 4000 lbs
- Electric Jack
- 24 Inch Lift
- Bolt-On
- Weld-On
- 1 Jack
- Stromberg Carlson
more information >
Product Page this Question was Asked From
Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jack
- Steel
- 3001 - 4000 lbs
- Electric Jack
- Bolt-On
- 1 Jack
- Lippert
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Replacement Lead Leg for Lippert Components Ground Control 3.0 Electric Leveling System - Qty 1
- Shop: Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Shop: Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC362485
- Q&A: Replacement Screw for Trailer Jack with 1-1/4 Inch Diameter
- Q&A: Dimensions of Weld Tabs and Diameter of Lippert Ground Control Leg # LC362485
- Q&A: Troubleshooting Lippert Power Jack Not Extending or Retracting But Motor Is Working
- Shop: Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Shop: Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear
- Q&A: Lippert Jack Motor Keeps Running But Leg Stops Moving When Leg Hits the Ground
- Shop: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Video: Fastway Flip Automatic Fold-Up Jack Foot Review FA88-00-6500
- Search Results: fastway flip
- Search Results: landing gear
- Shop: Replacement Mirrors
- Shop: Tailgate
- Shop: Towing Mirrors
- Search Results: location
- Search Results: wheel chock
- Search Results: wheel lock
- Search Results: trimax locks
- Search Results: flip down stabilizer jack
- Q&A: Where to Measure To Determine if Lippert Landing Gear Jack part # LG-1 Fits Trailer
- Q&A: Venture Landing Gear Rebuild Kits
- Q&A: Is there a Way to Identify 5th Wheel Trailer Landing Gear with No Markings
- Video: Bulldog Square Jacks Rebuild using Replacement Screw and Nut Assembly
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Video: Review of Lippert Components Camper Jack Replacement Override Nut - LC55FR