Correct Solera RV Slide-Out Awning for 72" Slide-Out

Question

Question:

my slide mesures 72 inches flang to flange whit size do i need

asked by: Stephen S

0

Expert Reply:

The correct Solera RV Slide-Out Awning for a 72" wide slide-out (flange to flange) is part # LCV000163279 for white or part # LCV000165063 black.

expert reply by: Conner L

0

Answer 1

When determining the correct size Slide-Toppers you need for your 2018 Laredo 330RL, you just need to measure your box width, which is measured on the outside front of box, including flange. Starting with your 72 inch box width, you will need the…

view full answer...

Answer 2

With the lack of clearance your options are more limited but you can still get a slide topper for your slide out. You will just have to realize you may not have full coverage of the slide out. You can down size to a smaller slide out topper that…

view full answer...

Answer 3

I understand the confusion Paul. According to Lippert, The Solera RV Slide-Out Awning part #LCV000163279 fabric measures 73" wide and the mounting rail measures 78" wide. This Slide-Out Awning fits RV Slide-outs between 68" - 73"…

view full answer...

Answer 4

You have found the correct slide toppers for your RV. The Awning #LCV000177334 is the correct one for 144" slide and the fabric measures 145". The Awning #LCV000165063 is the correct awning for a 73" slide and the fabric is 73".…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

When installing an awning like the Solera Smart Arm 12V Power RV Awning #LC517486, the arms will be secured to the wall framing. When the awning extends there will be quite a bit of leverage, so it is important to mount the awning to an area where…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Correct Solera RV Slide-Out Awning for 72" Slide-Out

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching