Does Curt Front Hitch Receiver C31078 Fit 2019 Ford F-350 2WD?

Question

Question:

Will the Curt Front hitch receiver mount on a 2019 2WD F350? Most comments are referring to 4WD models.

asked by: James K

0

Expert Reply:

Yes, the Curt # C31078 will fit both 2WD and 4WD models of 2019 Ford F-350.

expert reply by: John R

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 2

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 3

Hey Chad this is a great question. So the MORryde ALLTREK part #MR89DR does offer additional vertical suspension but it does sit a little taller than the equalizers it replaces so you wouldn't have to worry about your tires hitting fenders or…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

If you have the Ford 3" hitch then you can definitely add it but, yes it would change the weight capacity. The TorkLift Cannon Hitch Extension item #TLE1636 only has a 3,600 lbs towing capacity and a 360 lbs maximum tongue weight. If used with a…

view full answer...

Answer 7

Hey Ryan, the plate thickness of the CE Smith U-Bolt Plate part #CES95FR that you referenced is 7/32 inches.

view full answer...

Answer 8

The 1-5/16" Hellwig Adjustable Big Wig Rear Anti-Sway Bars are designed for 2WD #HE97MR or 4WD #HE94FR versions of your 2021 Ford F-250. These are both designed for trucks which have a stock ride height. Hellwig does offer their 2" Lift…

view full answer...

Answer 9

Hello Chris, it sounds like you are definitely on the right track here. When replacing an equalizer, it is critical that the replacement equalizer is identical in size to the original equalizer. There is a small amount of tolerance there, like maybe…

view full answer...

Answer 10

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 11

Yes, they are if your axles are overslung and the springs sit on top of them. The SumoSprings Trailer Helper Springs for 5-8K Axles item #SS26MV will work with a triple axle set up. They do a great job of absorbing road shock while also working to…

view full answer...

Answer 12

From the top of the bracket to the bottom of the rubber spring the #TFR350SDJ Timbrens measure about 7-1/2 inches. When installed you ideally want about a 1/2 inch to an inch of space between the Timbren and its contact point. However, to install…

view full answer...