Can the Curt Auxiliary LED Indicator Lights Be Used With a 7-Way

Question

Question:

I have a 7 pin connector on my tiffin motor home. I plug my wiring harness from my Jeep into this. I added a lift for My motorcycle. I now want to add your c53201 led kit to the back of my lift. So what is the best way to accomplish this? Since my c53201 Will be permanent should I just hardwire that into my wiring ? Or do you have a t tap plug? Thanks

asked by: Dave M

0

Expert Reply:

The Curt Auxiliary LED Indicator Lights part # C53201 would indeed need to be hardwired into the trailer lighting circuits if using a 7-way trailer connector as there is no tee and adapter combo I am aware of for this. It should just be a power and ground wire. I suggest the running light circuit for power.

expert reply by: Conner L

0

Answer 1

Thank you for your purchase of the Kuat NV 2.0 Bike Rack #NV22G! When it comes to lighting I have an alternate solution to what you're asking with the following parts: Curt Auxiliary LED Indicator Lights - #C53201 Thule License Plate Holder…

view full answer...

Answer 2

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 3

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack…

view full answer...

Answer 4

Yes, it does. The Hollywood Racks LED Light Bar item #HLY54RR is wired for a 4-way but comes with an adapter that will plug into a 7-way like yours to power the lights.

view full answer...

Answer 5

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 6

Thanks for reaching out, Tommy! The closest thing we have for your 2024 Honda CR-V is the Curt Trailer Hitch Receiver #C12169 which is a Class II hitch receiver. This means it has the same 1-1/4" receiver opening as the Class I but it just…

view full answer...

Answer 7

There is indeed a light kit made specifically for the Hollywood Rack Sport Rider SE #HLY84FR. I recommend the Hollywood Racks Safety LED Light Bar #HLY54RR. This is a 32" long LED light bar which will provide brake lights, running lights,…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Can the Curt Auxiliary LED Indicator Lights Be Used With a 7-Way

Product Page this Question was Asked From

Continue Researching