Seeking Bunk Board Carpeting 18 Inches Wide and 20 Feet Long

Question

Question:

I am looking for 18inch wide 20foot long for both bunks, do you offer that size?

asked by: Mark V

0

Expert Reply:

It sounds like you are looking for bunk board carpeting. The closest we have to your 18 inch by 20 foot is the CE Smith Deluxe Marine-Grade Carpeting for Bunk Boards - Gray - 18' Long x 18" Wide # CE11373 or Black # CE11349. This will give you a seam if you are using 20 foot long boards or even 18 foot boards as you will want to wrap the ends.

expert reply by: Jason S

0

Answer 1

In the video I attached on re-carpeting boat bunks we used lag bolts to attach the bunks to the hardware. Skip ahead to the 3:00 minute mark to see this.

view full answer...

Answer 2

The most common way to attach bunk carpet to bunk boards is to use heavy duty staples on the underside of the bunk and then an outdoor carpet adhesive on the tops of the boards. A coworker here used Liquid Nails as an adhesive when he did his two…

view full answer...

Answer 3

We do have a selection of bunk boards available which you can use for a variety of lengths. Below are the different lengths we carry: 2' - #CE27850 3' - #CE27800 4' - #CE27810 5' - #CE27820 6' - #CE27840…

view full answer...

Answer 4

Two 12 foot long bunks boards will work well to support your 21 foot boat. Ideally, the bunk boards should be at least half as long as your boat and run from the stern (or a few inches beyond it) to the bow as far forward as you like. Due to…

view full answer...

Answer 5

For a bearing kit that matches the bearing numbers and races you mentioned you would want the part #BK1-150 which includes the races and seals you'd need. You'd need a kit of these for each hub that gets replaced.

view full answer...

Answer 6

The inner and outer bearings should have a part number stamped on them. The grease seal typically has a number stamped on the rubber, as well. If you cannot find the number on the seal, the inner diameter of the seal can be used to find a…

view full answer...

Answer 7

No worries, you can easily construct some bunks yourself. Go to your local lumberyard and get some treated yellow pine 2x4x10 boards. You can then purchase some of the marine-grade carpet we offer, like part #CE11372. You'll need one roll per…

view full answer...

Answer 8

For starters, in order to use the CE Smith Self Centering Keel Roller for Boat Trailers part #CE29505 on your boat trailer you will also need to use the CE Smith Panel Bracket for 12" Boat Trailer Rollers part #CE10305G and the Roller Shaft with…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Seeking Bunk Board Carpeting 18 Inches Wide and 20 Feet Long

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching