Can the Buyers Products Safety Chain Clip # 337SC50B Install Vertically and Horizontally

Question

Question:

Which way is best to weld this bracket to the trailer frame? Vertical or horizontal?

asked by: David

0

Expert Reply:

Welding the Buyers Products Safety Chain Clip # 337SC50B either horizontally or vertically would be totally fine. Whichever orientation will work the best for your application will be totally fine.

expert reply by: Jameson C

0

Answer 1

Since your trailer weighs around 2000lbs and can tow up to 7000lbs I recommend using two of the 30" Long Safety Chain with 7/16" S-Hook with Latch - 5,000 lbs - Qty 1 #TCTSCG30-730-04x1 which have a combined weight rating of 10000lbs which…

view full answer...

Answer 2

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 6

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The WeatherTech Side Window Air Deflectors, #WT82476, include deflectors for the front and rear driver's-side and passenger's-side windows of your 2014 Chrysler Town and Country. The deflectors for the front windows are actually longer than…

view full answer...

Answer 9

When installing the WeatherTech Side Window Air Deflectors #WT82476, there is no adhesive strips used on the front deflectors. I have attached a link to an installation video for the deflectors on a 2015 Grand Caravan and as you can see in the video,…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Can the Buyers Products Safety Chain Clip # 337SC50B Install Vertically and Horizontally

Product Page this Question was Asked From

Continue Researching