94 inch 7k Dexter Axle that Has Brake Assemblies and Hub/Drums

Question

Question:

does this kit come with drums bearings and lug studs? im in need of a complete axle assemly, found the axle and now i need the stopping part with bearings

asked by: Allen W

0

Expert Reply:

The axle part # 8327864 does not come with hubs and brake assemblies but we have the part # 8327864-EB is the same axle that does include the brake assemblies and hub/drums like you are wanting.

expert reply by: Jameson C

0

Answer 1

The only physical difference of a 5,200 lbs axle item #e63GR and a 6,000 lbs axle item #e73GR is in the custom bend in the axle. This bend creates the zero camber angle for even road to tread contact. Both axles are 3" in diameter so they…

view full answer...

Answer 2

To pick out a replacement axle you need to first know the weight capacity you need, the distance between spring seats, and the distance from hub face to hub face and you'll be set. We don't have every length possible but we do have…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

94 inch 7k Dexter Axle that Has Brake Assemblies and Hub/Drums

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching