Rubber Grommet For 6-1/2" Oval Trailer Lights

Question

Question:

I also need the rubber grommet with this light do you have that in stock?

asked by: Bill D

0

Expert Reply:

The correct grommet for the Optronics Trailer Tail Light # ST70RB you referenced is the PVC Grommet for 6-1/2" Oval Trailer Tail Lights # a70gb.

It's a direct replacement for
Wesbar # 226088
Truck Lite # 60700
Grote # 92420
Peterson # 421-18
Bargman # 40-06-020
and will allow you to flush mount 6-1/2" oval lights.

I linked the parts above, as well as attached a video for you to check out.

expert reply by: Robert C

0

Answer 1

I looked up pictures of the light STIPP2R97 that you mentioned and I believe the closest LED option we have would be the Optronics Oval Lens #STL002RFB. I attached a review video for this light for you to check out as well.

view full answer...

Answer 2

If we are strictly speaking candela then the brightest oval 6-1/2" utility light we offer is the Optronics LED Trailer Utility Light part #BUL72CB which is rated at 123. If you can use a backup light then we offer the Optronics LED Backup…

view full answer...

Answer 3

I went out to the warehouse and checked all of our clear oval lights. The Sealed, 6-1/2 inch LED Clear Oval Trailer Utility Light, 10 Diode, item #BUL72CB, whiter light than the light emitted by the incandescent Oval Trailer Back Up Light, item…

view full answer...

Answer 4

Like the Custer Rubber Grommet #G65G, all the oval grommets we currently carry will be designed to fit a 6-1/2" light, like the Optronics LED Trailer Tail Light #STL72RB. However, we do have the Replacement Lenses and Housings #27-9904,…

view full answer...

Answer 5

Both the #BUL10CB and the #BUL72CB are 10 diode lamps, and therefore neither lamp would really be brighter than the other. The main difference between the two is how the light is focused. Because the #BUL10CB lamp is DOT compliant as a back-up light,…

view full answer...

Answer 6

There is an LED version of the #ST70RB with the part #STL70RB.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Rubber Grommet For 6-1/2" Oval Trailer Lights

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching