Replacement 3,500 lb Coupler for Atwood 82311

Question

Question:

3500# COUPLER ATWOOD 82311. It doesnt appear that this is available any longer. Is there a replacement that meets the same specs?

asked by: Kevin S

0

Expert Reply:

You are correct that the Atwood 82311 is no longer available, but there is a similar coupler with the same specs, which are a 3,500 lb capacity, couples to a 2 inch hitch ball and fits a 3 inch channel. For that I recommend the Trailer Coupler 2" Ball 3" Channel Tongue (3,500 lbs.) by Dutton-Lainson # DL13800

This has the same specs as the Atwood.

expert reply by: Kyle S

0

Answer 1

It sounds like you are looking for a caster wheel for a trailer jack. If that is the case then we do have some options like the Ram Removable Assembly part #JC-101 for a 2" outer tube and 1-3/4" inner tube.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 6

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

I recommend etrailer.com Channel Tongue Coupler part #CT-5003-Z to replace the Shelby 5135 coupler. The etrailer.com coupler has a channel width of 3" and takes a 2" ball. It also has 3" from center of bolt hole to center of bolt hole…

view full answer...

Replacement 3,500 lb Coupler for Atwood 82311

Product Page this Question was Asked From

Continue Researching