Attaching Wishboned Trailer Wiring to Standard Wire

Question

Question:

white to white,green to green.yellow to yellow,Due i put the two brown wires with the brown wire.

asked by: Doug M

0

Expert Reply:

Yes, it sounds like you are attaching wishbone trailer wiring for the running light circuit to a standard single wire running light circuit so you would run the two brown wires to the single brown and you'd be set.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 7

The Replacement Hardware Kit #AABRKT-5056 will fit the Aries Pro Series Grille Guard #AAP5056. This is the upgraded version of the Grille Guard #AA5056 which uses the same install hardware to attach to a truck.

view full answer...

Answer 8

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 9

Hey Jeff, The Pace Edwards JackRabbit Retractable Hard Tonneau Cover w Explorer Rails #311-JED7833 is designed for a 6-1/2' bed while the #311-KRD7936 is designed for an 8' bed. Since you have a 6-1/2' bed the #311-JED7833 would be the…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

If you have the Gooseneck versions of the Curt CrossWing ( #C92DR or #C32DR) you unfortunately would not be able to use the Rota-Flex with it. The pivoting head causing too much strain for the single point of contact you have with a gooseneck hitch.…

view full answer...

Answer 12

Installing ta Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Adapter Pin Box like the #325-GH-8045 would not void the warranty of your camper, and Gen-Y makes some of the most durable parts on the market. I really like this as an alternative to…

view full answer...

Attaching Wishboned Trailer Wiring to Standard Wire

Product Page this Question was Asked From

Continue Researching