Does Rhino Rack Roof rack for Factory Tracks Fit Tracks on SnugTop Camper Shell

Question

Question:

I have a SnugTop shell on the back of my truck that already has factory installed rails. Can you tell me if the Y02-490B-NT Rhino will fit the SnugTop? Will I require any adapters? Thanks.

asked by: Frank

0

Expert Reply:

The Rhino-Rack Roof Rack for Factory Tracks # Y02-490B-NT that you referenced is a direct fit for the factory tracks you have on top of your SnugTop camper shell. This comes with everything you'd need too so you wouldn't need any additional parts.

expert reply by: Jameson C

0

Answer 1

The Black Aero Crossbars that are the same as the Silver Crossbars, part #Y02-480-NT that you mentioned, is part #Y02-480B-NT

view full answer...

Answer 2

The Rhino Rack Roof Rack for Factory Tracks part #Y02-480-NT that you referenced will fit in Yakima roof rack tracks.

view full answer...

Answer 3

We have the Rhino Rack Roof Rack for Thule tracks part #Y02-480-NT which will fit the tracks on your camper shell and also provides an aero shaped bar like what your kayak carrier is designed to fit.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 10

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Does Rhino Rack Roof rack for Factory Tracks Fit Tracks on SnugTop Camper Shell

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching