Is Trimming Required to Install Westin HDX Grille Guard on a 2010 Dodge Ram 2500

Question

Question:

IS THERE ANY CUTTING OR TRIMMING ENVOLVED IN MOUNTING THIS UNIT ON MY TRUCK?

asked by: JOHN C

0

Expert Reply:

There is minor trimming required on the lower valance for the bottom brackets on a 2010 Dodge Ram 2500. However since it is the lower valance and the view of it would be blocked by the grille guard anyway the trimming should not be noticeable. I have included a link to all of the grille guards that fit your truck.

expert reply by: Michael H

0

Answer 1

The tow hooks will remain on your 2016 Ram 2500 when installing Westin HDX grille guard #57-3550. I have included a picture that shows the guard installed and you can see the tow hooks still in place.

view full answer...

Answer 2

Assuming you have the Westin HDX #57-3550 or #57-3555 Grille Guard, you'll need the #57-355PK replacement hardware kit. I looked up the vehicle fits, and the 2018 Ram 3500 and the 2014 2500 use the same HDX Grille Guards. Keep in mind that not…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 10

The measurement you're referring to for the Erickson Removable Motorcycle Wheel Chock #EM07506 is 8". This wheel chock has overall measurements of 11-3/4" long x 8-1/4" wide x 8-1/2" tall and will fit tires up to 6"…

view full answer...

Answer 11

To activate the brakes on a trailer with your 2024 Toyota Grand Highlander you'll need a 7-way connector and brake controller. To switch over from your 4-pin connector you can install the #ETBC7L. This will plug into your 4-pole connector and…

view full answer...

Answer 12

Hey Jerry, the install of the Aries Bull Bar part #AAB35-4015 do require you to permanently remove the tow hooks to install. It looks like the similar Westin Ultimate Bull Bar part #32-3645 does allow you to keep them though.

view full answer...

Is Trimming Required to Install Westin HDX Grille Guard on a 2010 Dodge Ram 2500

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching