Short 6 Inch Handle for Dutton-Lainson Winch DL2000A

Question

Question:

Hello do you have a short 6 inch replacement winch handle for a Dutton-Lainson winch model DL2000a ???

asked by: Kurt

0

Expert Reply:

We do have a short 6 inch handle that will work with the model DL200A Dutton-Lainson Hand Winch # DL14725.

The correct part is the Replacement Winch Handle for Dutton Lainson Winch - 6" # DL70336.

expert reply by: Kyle S

0

click to enlarge

Answer 1

I did some research on the 1998 18 foot Pro Craft 180 and from what I could find it weighs about 2,090 lbs. If your trailer does not have rollers or wood bunks you will need a winch that is rated for half the weight of the boat. I recommend the The…

view full answer...

Answer 2

The Replacement Winch Handle for Dutton Lainson Winch, part #DL70336 is designed to fit Dutton-Lainson winches like part #DL15502. I went to our warehouse and measured the #DL15502 shank the handle fits. The shank measures .46 X .625 inches. I have…

view full answer...

Answer 3

The handles for the Dutton-Lainson Single Speed Winches feature a mounting hole size that is a bit larger than what is on the handle for your existing Shelby Model 5404 Winch. We do have the Replacement Handle for Fulton Hand Winch #F501110 that…

view full answer...

Answer 4

I was able to verify with the manufacturer, Dutton-Lainson, the exact replacement handle you need for your Dutton-Lainson 2000A winch, which is the following part number: - Replacement Quick Attach Winch Handle for Dutton Lainson Winch #DL70330

view full answer...

Answer 5

We do have the exact replacement handle you need for the Dutton-Lainson 2000A Hand Winch; the correct part is the following: - Replacement Quick Attach Winch Handle for Dutton Lainson Winch #DL70330

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Short 6 Inch Handle for Dutton-Lainson Winch DL2000A

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching