Fifth Wheel Rail Kit that Fits 2002 Dodge 2500 Long Bed

Question

Question:

will this rail kit fit my 2wheel drive 2002 2500 8 ft bed

asked by: Phill Y

0

Expert Reply:

We have fifth wheel rail kits that fit your 2002 Dodge Ram 2500 long bed with the part # RP30035 but the kit you mentioned does not fit your truck.

expert reply by: Jameson C

0

Answer 1

For your 5th wheel towing, I recommend the 2008 Chevy 2500 with the 6.6L V8 Duramax which based on the cab and bed length as well as drive axle will have different towing limits. I've listed them below: 2500 Reg Cab Long Bed (LB) 4WD--15,500…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 5

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept…

view full answer...

Answer 6

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 7

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 8

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This…

view full answer...

Answer 9

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 10

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the…

view full answer...

Answer 11

Hey Cody, you are installing this B&W Turnoverball #BWGNRK1020 on a 2021 Chevy 2500 correct? If so, the M14 bolts are definitely the correct size. It is possible that the holes in the frame are corroded which is preventing the bolts from…

view full answer...

Answer 12

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth…

view full answer...

Fifth Wheel Rail Kit that Fits 2002 Dodge 2500 Long Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching