How High Above the Bed will UWS UWS07642 Toolbox Sit

Question

Question:

What is the height above the bed?

asked by: Peter

0

Expert Reply:

The top of the lid of the UWS # UWS07642 truck bed toolbox will sit 2-3/4 inches above the top of the bed side.

To find where the bottom of the box will sit, measure from the top of the bedside down by 11-1/2 inches, that is exactly the height that the bottom of the box will sit at. I've linked you to a product description video for the # UWS07642 truck bed toolbox.

expert reply by: Mike L

0

click to enlarge

Answer 1

The fifth wheel pucks of your OEM rail kit are different from the gooseneck ball that's in the center of your bed. While it does seem odd I can see how they would rate the two differently. The B and W Hitch part #BWRVK3305 does fit your 2019 Ford…

view full answer...

Answer 2

It can be difficult to give a truly accurate estimate for the length of time it takes to install the Custom Third Brake Light Camera for 8" Factory Monitor #3460001 on your 2020 Ford F-350 Super Duty. The time really depends on how comfortable…

view full answer...

Answer 3

There is a B&W Companion fifth wheel hitch that will work if you have the factory fifth wheel/gooseneck prep package in your 2012 Ford F-250 or F-350 Super Duty, but it mounts in the puck system of your truck instead of using the gooseneck. If…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 9

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 10

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 11

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 12

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...