Thule Truck Bed Tailgate Pad and Bike Rack That Fits 2019 Chevrolet Silverado 1500

Question

Question:

TH823PRO. Will this fit a 2019 Chevrolet Silverado 1500?

asked by: Randall S

0

Expert Reply:

We do have a Thule GateMate Pro Tailgate Pad and Bike Rack that fits a 2019 Chevy Silverado 1500, though it is a different one than you mentioned.

The correct fit for a 2019 Chevy Silverado 1500 is the Thule GateMate Pro Tailgate Pad and Bike Rack # TH824PRO.

I have added some photos showing this on a '19 Silverado 1500 as well as a link to a video review showing it in use on this same truck.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The Inno Velo Gripper Bike Rack #INRT201 can grab bike frames that are up to 1.03 inches in diameter. For mountain bikes that have wider frames you can instead attach the rack to the seat post. Or you could use a bike frame adapter bar part #UB01.…

view full answer...

Answer 2

For the 2020 Chevy Colorado I recommend to use 2 sets of the Inno Velo Gripper Bike Rack for Truck Beds - Clamp On part #INRT201 which easily clamp on the bed rail and hold the bike with it's rod and ratcheting strap system. We have had a lot of…

view full answer...

Answer 3

I went out to our warehouse to take a few measurements on both the clamp and mounting plate for the Inno Velo Gripper Bike Rack #INRT201. The black plate measures 4 inches long and 2-3/8 inches wide with a small lip that measures 1 inch wide. The bed…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

I really like the Curt Trailer Hitch Receiver #C14108 for your 2005 Chevy Silverado 2500HD Short Bed because it has a hidden crosstube and is a Class IV rating so it's nice and sturdy for up to 10K trailers or 12K trailers if a weight…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

Hey Jerry, the install of the Aries Bull Bar part #AAB35-4015 do require you to permanently remove the tow hooks to install. It looks like the similar Westin Ultimate Bull Bar part #32-3645 does allow you to keep them though.

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...