Troubleshooting Rubber Pads Of B&W Biker Bar Coming Unglued From Metal Bar

Question

Question:

The bar was tight on the frame but the rubber pads came unglued during transport. What glue do you recommend for regluing so this wont happen again?

asked by: Rob W

0

Expert Reply:

With the pads coming unglued on your Replacement Bar for B&W Biker Bar Motorcycle Tie-Down System # BWMC2302B, I recommend using the Loctite QuickTite Super Glue Gel - Instant Adhesive - 0.14-Oz Applicator # LT39123. This adhesive is designed for metal and rubber use, so it will work well and is designed to tolerate stresses like shock, vibration, and impact.

expert reply by: Jason S

0

Answer 1

The Replacement Bar for B&W Biker Bar Motorcycle Tie-Down System #BWMC2302B is the replacement bar that fits H-D Dyna, Softail, and V-Rod bike frames. The #BWMC2301B is the Replacement Clamping Bar for B&W Biker Bar Motorcycle Tie-Down for…

view full answer...

Answer 2

The B&W Biker Bar Motorcycle Tie-Down System Base with Anchor Plates #BWMC2300 does not need to be adjusted to the higher holes. The adjustability is dependent on the ground clearance of your frame. The B&W Biker Bar Motorcycle Tie-Down…

view full answer...

Answer 3

Yes, the B&W Biker Bar Motorcycle Tie-Down Systems all use the same base and anchor kits. So all you would need to do is buy the Replacement Clamping Bar for B&W Biker Bar Motorcycle Tie-Down for Harley-Davidson Touring #BWMC2301B and replace…

view full answer...

Answer 4

The B&W Biker Bar that you should be using for your 2010 Ultra Classic is the part #BWMC2301 but for your 2014 Softail Deluxe you need the Biker Bar #BWMC2302 instead. Good news is that both options use the same base system so you just need to…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Troubleshooting Rubber Pads Of B&W Biker Bar Coming Unglued From Metal Bar

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching