What are the Overall Dimensions of the Dexter Agricultural Hub Assembly # AH15450ECOMP
Question:
Do you have overall outer dimensions for this hub? Perhaps simple dimensioned drawing?
asked by: Eric C
Expert Reply:
I pulled the Dexter Hub Assembly, # AH15450ECOMP, from the warehouse and made a simple diagram showing the outer dimensions for you to check out, see photo. This hub comes with the bearings, seal, grease cap and lug bolts.
This hub fits spindle # TRU54FR. If you are not sure what spindle you have or if this hub will fit on your spindle, then you can compare the part numbers of your current bearings to those with this hub assembly or you can take a few measurements of your spindle. The part numbers of your bearings will be stamped into the bearing and in the rubber of the grease seal. If you are unable to locate the part numbers or you no longer have the old bearings, then you can take a few measurements of your spindle to determine what bearings you have. I have also attached a photo showing where to locate the bearing and seal part numbers as well as where to measure on your spindle.
This hub has a 1,500 lb weight capacity and is designed to be used with a 3,000 lb axle. Keep in mind that this is an agricultural hub and is designed to be used with low speed applications such as farm equipment or machinery.
Products Referenced in This Question
Agricultural Spindle for 3,000-lb Trailer Axles - 1-5/8" Diameter
- Trailer Spindles
- Agricultural Spindle
- 1-5/8 Inch Diameter
- Round
- For 3000 lb Axle
- TruRyde
more information >
Product Page this Question was Asked From
Trailer Hub Assembly - 3,000 lbs Axles - 4 on 5 - Agricultural
- Trailer Hubs and Drums
- Hub
- Agricultural
- LM67048
- LM11949
- For 3000 lbs Axles
- 1/2 Inch Stud
- 4 on 5 Inch
- TruRyde
more information >
Continue Researching
- Shop: Trailer Hub Assembly - 3,000 lbs Axles - 4 on 5 - Agricultural
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Video: Dexter Axle Trailer Hubs and Drums - Hub - 84555UC1-EZ Review
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Firestone Coil-Rite Air Helper Springs - Rear Axle
- Shop: Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: 118646
- Search Results: aluminum trailer coupler
- Search Results: 119148
- Search Results: 119190
- Search Results: flexiride
- Search Results: c59496
- Search Results: 119191
- Video: Lock N Roll 3-Position Channel Articulating Hitch Review
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 5-1/2
- Shop: Replacement Oil Cap Kit for 9,000-lb to 15,000-lb Dexter Axle
- Q&A: Parts Needed To Secure A Slide Out Outdoor Kitchen In An RV
- Q&A: Availability of Hub and Drum to Fit 1.25 to 0.75 Tapered Spindle
- Q&A: Can a 5-Lug Trailer Hub Replace a 4-Lug if the Bearings and Seals are the Same
- Q&A: Recommended Idler Hubs For 1 Inch Diameter Spindle On Boat Trailer
- Q&A: Replacement Hub With An Out Bearing And In Bearings That Measure .74" and 1.25" For 5 On 4.5 Wheel
- Q&A: Recommended Flat Towing Parts for a 2024 GMC Canyon Denali
- Q&A: Recommended Hub for 3K Trailer Axle with 1.25" Inner and .75" Outer Bearing
- Video: Kenda Tires and Wheels - Tire with Wheel - AM30153 Review
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-G-EZ-1K Review
- Shop: Trailer Hitch
- Video: CE Smith Trailer Hubs and Drums - Hub - CE13511 Review
- Video: CE Smith Trailer Hub Assembly Review and Installation
Greg
4/3/2024
John I need to build some yard trailers to move engine blocks around. I have some Titan #16858 hubs that I want to use so my question is will they work on this spindle? The bearing dimensions all match the hubs, but I need to verify the O/S to O/S dimensions between "C" & "D" and between "B" & "D". Is there anyway you find those numbers for me? Thank you for your help.