Weight Distribution Hitch for Pop-Up Camper With 2,000 lb GVWR

Question

Question:

I have a 2006 Viking epic 2308 st. I’ve read before that weight distribution hitches aren’t compatible with many pop up campers. Can you help explain if they do or don’t work? I’m towing with a 2008 Chrystler Town and Country touring. Thank you!

asked by: David D

0

Expert Reply:

Weight distribution hitches are compatible with pop-up campers so long as they have a trailer frame that is up to 6 inches tall and a place for the brackets that is 27" to 30" back from the center of your coupler.

If your 2006 Viking 2308 has that then it is compatible with a weight distribution system. According to my research your camper has a GVWR of slightly over 2,000 lbs; I recommend verifying this and if so I highly recommend the Fastway e2 Weight Distribution # FA92-00-0450.

I really like this system because it represents a fantastic value for a weight distribution hitch. It provides excellent sway control and leveling, has brackets and trunnion bars which make it easier to set up than other systems, but is at a much better price point than alternatives. It comes with everything you need except for the hitch ball, the 2" Hitch Ball # 40038.

I have added a link to a video review for you as well of the Fastway e2 Weight Distribution # FA92-00-0450.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Anytime the fully loaded and ready to tow trailer weight is greater than 50 percent of the weight of the tow vehicle, using weight distribution should be considered. When you get the pop-up, hitch it to the vehicle and pay special attention to the…

view full answer...

Answer 2

Grease caps just pop out and in. The best way to get them out is to pry them with a flat head screw driver or tap them from side to side with a hammer. To install new ones, you simply gently hammer them in. Normally I use a short piece of 2x4, to…

view full answer...

Answer 3

Bearing Buddies are a great way to keep grease in a trailer hub. I recommend them as long as you are aware that it's very easy to put too much grease in a hub with these which will blow out the seal. They have no problem being used on longer road…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Weight Distribution Hitch for Pop-Up Camper With 2,000 lb GVWR

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching