Picking Out Replacement Awning Fabric for 2008 Pilgrim Open Road 358RL

Question

Question:

Measuring our awning makes it 175...do I order the 18foot or the 17. We have an AandE Awning. We have a 2008 Pilgrim Open Road Fifth Wheel, Model 358 RL 4S-5.

asked by: Melissa W

0

Expert Reply:

To determine what size fabric you need, measure your awning from the center of the left arm to the center of the right arm. Do not order based on the actual fabric width, as it will arrive too short. So if that distance measured is 17 feet the part # LCV000334413 that you referenced is the correct kit you'd need. If you need 18 feet instead you'd want # LCV000334423.

expert reply by: Jameson C

0

Answer 1

I checked with Roadmaster and verified the correct front anti-sway bar for your Class A 2017 Ford F-53 chassis with a 18,000 lb GVWR; it is the following part number: - Roadmaster Front Anti-Sway Bar #RM-1139-148

view full answer...

Answer 2

Yes, the front #TFFF53B Timbren suspension enhancement are similar to the front #SSF-170-40-2 SumoSprings for your 2018 Thor ACE 30.2 Motorhome. Timbren is a little more well-known but we have received feedback from our customers that the SumoSprings…

view full answer...

Answer 3

According to my research your 2019 Jayco Alante 29S is built on a Ford F-53 chassis with a GVWR of 18,000 lbs. Since this is the case the correct SumoSprings for your front axle is part #SSF-170-40-2. Attached is an installation video of these being…

view full answer...

Answer 4

I reached out to my contact at Timbren and this is something that is not all that uncommon. If the brake lines on the axle of your 2013 F53 Chassis are underneath the Timbren Rear Suspension Enhancement #TFRF53A you can carefully bend them out of the…

view full answer...

Answer 5

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Sorry Jennifer, I am a bit confused as you were looking at the Replacement U-Clamp Bracket #RM-B141 which mounts with bolts and not U-bolts. This part works with the Split Bushing #RM-205217-10 for the discontinued Roadmaster Front Anti-Sway Bar…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...