Which Timbren Kit Fits 2014 Itaska Sunstar 31ke

Question

Question:

I have a 2014 Itaska Sunstar 31ke There are three different model numbers for the front springs offered by Timbren. What are the differences? I tow a Jeep Wrangler with a tow dolly also. Thanks

asked by: Marco

0

Expert Reply:

I checked with Timbren and for your 2014 Itasca Sunstar 31ke the correct fitting kit is the part # TFFF53B based on the chassis and there aren't any other options that fit.

expert reply by: Jameson C

0

Answer 1

Although your 2011 Thor Hurricane 32A Motorhome is built on the F-53 chassis, not everything for the F-53 will fit. In this case, your only option for front suspension enhancement is the Timbren Front Suspension Enhancement System #TFFF53B. There…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

For your 2024 Ford F-53, I recommend checking out the Timbren Front Suspension Enhancement System #TFFF53B for the front, and the Timbren Rear Suspension Enhancement System #TFRF53A for the rear. These kits do not require drilling, will replace your…

view full answer...

Answer 10

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 11

The air suspension system on your 2022 Ram 2500 limits your options for suspension enhancement. None of the air bags made for your truck will be compatible. Instead, I recommend adding the SumoSprings Rebel Custom Helper Springs #SS64VR. The…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Which Timbren Kit Fits 2014 Itaska Sunstar 31ke

Product Page this Question was Asked From

Continue Researching