Valve Relocation Kit Needed for Big Tex 22HG Trailer

Question

Question:

I am looking for some valve stem extenders for my trailerBig Tex 22HG, its got 16 wheels 10,000 pound dexter axles. thanks

asked by: Kinson C

0

Expert Reply:

We have 2 different kits for you to choose from and it all depends on if you need a 45 degree bend in the hose, kit # WM8208, or a more severe 135 degree bend in the hose, kit # WM8001-135.

Attached is an installation video of the kit with the 135 degree bend that you can check out.

expert reply by: Jon G

0

Answer 1

Based on my research a Big Tex 16ET trailer uses a 17.5" x 6.75" wheel with an 8-bolt lug pattern and uses ST215/75R17.5 load range H tires. The Provider 215/75R17.5 Radial Tire w/ 17-1/2" Silver Mod Wheel #TA95ZR you referenced is a…

view full answer...

Answer 2

I have a couple things you can check that may help you. First check to make sure you have the most up to date version of the Curt Echo app and that your app has permission for Bluetooth active. Also in the app you will need to make sure that a manual…

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...