Lock Pin Hole Measurement for Class I Hitch

Question

Question:

What is the distance of the lock pin hole to the forward end of the mount? Some are too long to fit my drawbar. Thanks!

asked by: Bob

0

Expert Reply:

The distance from the center of the hitch pin hole to the end of the drawbar is 1-9/16 inches. This is a Class I drawbar. Class II drawbars will not fit in the Class I hitch and have a distance of approximately 2 inches from the center of the hitch pin hole to the end of the drawbar.

expert reply by: Robert G

0

Answer 1

I am not sure how much you are looking to spend but bike racks that are capable of handling the weight of two electric bikes are not going to be cheap because they must be built much stronger. However, we do have an excellent option for you in the…

view full answer...

Answer 2

Class I trailer hitch receivers like #24847 have a distance of about 1-5/8 inches from the center of the hitch pin hole to the welded stop in the back of the hitch receiver tube. Class I ball mounts like #3594 normally are about 1-9/16 inches from…

view full answer...

Answer 3

Typically the distance from the center of the hitch pin hole on a 1-1/4 inch hitch to the face of the opening on the hitch measures 2 inches whereas on a 2 inch hitch the distance is 2-1/2 inches.

view full answer...

Answer 4

I went out into the warehouse to get the measurements you requested for the Draw Tite Hitch part #36523. The distance from the center of the hitch pin hole to the opening of the hitch is 2-1/8 inches. The distance from the center of the pin hole to…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 10

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 11

Hey Dave, so the best option for carrying your carbon frame bike and e-bike is the Swagman Escapee part #S39SR with the ramp #S59SR . It has the capacity for carrying an e-bike, is rated for travel trailer use, only touches the bikes by the tires…

view full answer...

Answer 12

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Lock Pin Hole Measurement for Class I Hitch

Product Page this Question was Asked From

Continue Researching